Grit classifier

The BOEEP’s Easy Operation Stainless Steel Shaftless Screw Grit Removal for Municipal Waste Water Treatment Plant Model WSF is an advanced item to make waste water treatment more simple and effective. The item eliminates the need for manual separation of grit from wastewater, thus reducing work expense and increasing general effectiveness. The WSF grit treatment system is established during the inlet end of the waste water treatment plant and it's also created specifically to remove grit as well as other materials which will harm downstream equipment, thus reducing the upkeep of the plant.

The BOEEP’s Easy Operation Stainless Steel Shaftless Screw Grit Removal for Municipal Waste Water Treatment Plant Model WSF was manufactured from good quality stainless steel that makes it resistant to corrosion and lasting. The appearance of the grit reduction system eliminates the requirement for a shaft, that makes it an easy task to run and keep. The screw conveyor is driven by means of an engine, which is managed by means of a programmable logic controller(PLC), supplying a precise and dependable procedure.

The WSF grit reduction system was created to manage big volumes of grit as well as other materials contained in the waste water. The item can capture the majority of grit particles, which helps it be dependable and efficient. Also, this system has a self-cleaning procedure which helps to ensure that the grit closet is actually clean and prepared to be utilized.

Installation of the BOEEP’s Easy Operation Stainless Steel Shaftless Screw Grit Removal for Municipal Waste Water Treatment Plant Model WSF is not difficult and needs minimal effort. The item comes complete with all needed to be done should be to place the grit removal system through the inlet end connected with wastewater treatment plant and plug it in. When set up, the grit reduction system is totally automatic, needing minimal manual intervention.

The BOEEP’s Easy Operation Stainless Steel Shaftless Screw Grit Removal for Municipal Waste Water Treatment Plant Model WSF provides numerous advantages, including increased effectiveness, paid down upkeep expense, and reduced work rate. The device is simple to use, requires minimal upkeep, and green. Its high grit capture and self-cleaning procedure make sure it is a dependable and efficient addition to any waste water treatment plant.

The BOEEP’s Easy Operation Stainless Steel Shaftless Screw Grit Removal for Municipal Waste Water Treatment Plant Model WSF is an item that is perfect to any waste water treatment plant. The item is simple to install, easy to operate, and require minimal upkeep. Its high capture rate of particles, and self-cleaning mechanism ensure it is a reliable and efficient system. Invest in BOEEP's grit treatment system today and revel in the huge benefits it has

Why Choose Us

Product Description

Boeep screw grit removal belongs to light type grit and water separation equipment. It can either be a stand-alone unit, can work in conjunction with the Grit Vortex Separator as well. The concentrated grit from the Grit Vortex Separator is airlifted or pumped to the classifier for further separation, dewatering and removal. The WSF is mainly used for municipal sewage treatment plant

It consists of driving unit, auger, water tank, U-shape chute and liner strip. The screw type grit removal is composed of a slope bottom tank and a screw conveyor. The grit settled at the bottom of the tank is collected, lifted by the screw conveyor(25degree) and then drained and discharged to make sure the moisture content of the discharged grit flow be less than 60%. The screw diameter and consequently the grit classifier model varies according to the volume of grit to be dewatered

Product Features

1- Using the screw conveyor without the bearing underwater, to decrease maintenance needs

2- Lined inside the U trough with low friction, wear resistant material, easy to be changed

3- Integrated equipment which is convenient for installation and transportation

4- Cost-effective, easy operation, easy installation

Model Choice

Model	Shaftless screw grit classifier							Shaft screw grit classifier
		WSF260	WSF320	WSF360	WSF420	LSF500	LSF600	LSF750
External diameter of screw - mm	220	280	320	380	500	600	750
Capacity - m3/h	18-43	43-72	72-97	97-126	600	1000	1800
Power - kw	0.37			0.75	1.5	3	5.5	5.5
Speed - r/min	5			4.8			5.2			4
Particle diameter - mm	≥0.2

Production Site

Project Site

Related Products

About Us

FAQ

Q: Are you trading company or manufacture
A: We are both manufacture and trading company. We have over 20 years' professional experience as a waste water treatment equipment manufacturer and engineering service enterprise

 

Q: Where is your factory located
A: Yangzhou City, which is very close to Shanghai with only less than 3 hours' driving

Q: Do you provide OEM service
A: Yes. Any required logos is available

Q: How about the production capacity of your company
A: Our factory covers area over 20,000M² and produces machines 2000 sets per year

Q: How could we trust you and your company? This is first time transaction
A: Our company has more than 20 years professional experience. We cooperate over 1000 customers in China and overseas. We export nearly 40 countries all over the world. Welcome to our company and watch our plant production condition any time

Q: What certificates do you have
A: CE/ISO/SGS

Q: Do you offer after-sales service
A: Yes. Engineers available

Q: How long is your warranty
A: One year after the arrival of the goods. During this period, as long as it is not a man-made damage, we send the damaged parts free of charge

Q: What about your delivery time
A: Normally within 45 days against down payment

Q: What about the package of your export product
A: We use anti-corrosion wooden case with foam inside

Q: What kind of payment do you accept
A: T/T, L/C, PAYPAL, Cash, D/P, D/A, WESTERN UNIION, MONEYGRAM

Q: What kind of transportation do you offer
A: Customers decide freight mode, Air, Land & Sea